HAWE V60N Series Hydraulic Pump

Overview: variable displacement axial piston pump type V60N

HAWE V60N Variable displacement axial piston pumps adjust the geometric output volume
from maximum to zero. As a result they vary the flow rate that is provided to the
consumers.
The variable displacement HAWE V60N axial piston pump type V60N is design for open circuits
in mobile hydraulics and operates according to the swash plate principle. It is
available with the option of a thru-shaft for operating with additional hydraulic
pumps in series.
HAWE V60N is mostly mount on power take-offs in commercial vehicle gearboxes.
The range of pump controllers allows the axial piston pump to use in a variety of
applications.

HAWE V60N Features and benefits

Optimized power-to-weight ratio
Broad selection of controllers
Slim design matching PTO (power take-off)
Thru-shaft compatibility
High self-suction speed
Intended applications
Municipal trucks
Fire trucks
Loading cranes and elevating work platforms
Tipper trucks and skip trucks
Suction dredgers and sewer cleaning vehicles

Installation, operation and maintenance information

1 Intended use

This product is intend exclusively for hydraulic applications (fluid technology).
The user must observe the safety measures and warnings in this document.
Essential requirements for the product to function correctly and safely:
All information in this documentation must observe. This applies in particular to all safety measures and warnings.
The product must only be assembled and put into operation by specialist personnel.
The product must only be operated within the specified technical parameters described in detail in this document.
All components must be suitable for the operating conditions when using an assembly.
The operating instructions for the components, assemblies and the specific complete system must also always be observed.
If the product can no longer be operated safely:
1. Remove the product from operation and mark it accordingly.
It is then not permitted to continue using or operating the product.

 

2 Assembly information

The product must only be installed in the complete system with standard and compliant connection components (screw fittings, hoses,
pipes, fixtures etc.).
The product must be shut down correctly prior to disassembly (in particular in combination with hydraulic accumulators).

 

2.1 General information

The variable displacement axial piston pump is suitable for use in an open or semi-closed circuit.
The pump can be flange-mounted on the usual mounting points (e.g. gearbox power take-off, combustion engine or electric drive,
cardan shaft) using a flange mounting. Suitable coupling flanges are available as accessories for attachment to a cardan shaft "coupling
flanges for cardan shafts".
In order to reduce the weight torque of the pump, a separate support can be attached in addition to the flange mounting. For this
purpose, M10 threads are included in the pump housing (only V60N-090/110/130)see Chapter 4, "Dimensions" A change of rotating
direction is available for types V60N-060, V60N-090 and V60N-110 variable displacement axial piston pumps. For conversion instructions, please get in touch with HAWE Hydraulik SE. The housing pressure in the pump must always be greater than or equal to the
ambient pressure.

During assembly, note the following principles:

1.Only trained persons are allowed to mount or remove the pump.
2.Always ensure absolute cleanliness to prevent contamination from affecting the pump.
3.Remove all plastic plugs before operation.
4.Avoid installation above the tank .
5.Observe the electric reference values.

principle part2

6.Before initial use, flll the pump with hydraulic fluid and bleed. Automatic pump fllling via the suction line by opening the drain ports
is not possible.
7.Always supply the pump with hydraulic fluid from the start. Even just a short period with insufficient hydraulic fluid can damage the
pump. Such damage is not immediately visible once the pump is put into operation.
8.Never drain the pump.

principle part3

9.Hydraulic fluid which flows back into the tank must not be sucked back in immediately (install baffles!).
10.If there is a check valve installed in the leakage line, negative pressure may occur in the pump housing during operation. If this
happens, install an auxiliary pump to flush the housing.
11.Before first use, run the pump for approx. 10 minutes at max. 50 bar after initial start-up.
12.The leakage line must be installed in the tank in such a way that it ends below the oil level. The end of the leakage line should be
13.positioned roughly equidistant from both the bottom of the tank and the oil level.
14Do not use the entire pressure range of the pump until it has been thoroughly bled and flushed.
15.From the start, always keep the temperature within the specified range (see Chapter 3, "Parameters"). Never exceed the maximum
temperature.
16.Always comply with the cleanliness level of the hydraulic fluid. In addition, filter the hydraulic fluid appropriately (see Chapter 3,
"Parameters").
17.Self-installed filters in the suction line must be approved beforehand by HAWE Hydraulik.
A system pressure-limiting valve must be installed in the pressure line so that the maximum system pressure is not exceeded.

HAWE V60N Mode NO.

V60N-060LDYN-1-0-03/LSNR-2-300

V60N-060RDYN-2-0-03/LLSN-350-C011

V60N-060RSFN-1-0-03/LLSN

V60N-060RSFN-2-0-03/LLSN–C014

V60N-060-RSFN-2-0-03/LSNR-350

V60N-090LDUN-1-0-03/LSN-2

V60N-090LDYN-1-0-03/LSNR-2-300

V60N-090LSFN-1-0-03/LSNR/ZW-2

V60N-090LSFN-2-0-03LSNR/ZW

V60N-090LSUN-1-0-03/LSN

V60N-090LSUN-1-0-03/LSN-

V60N-090RDUN-1-0-03/LSN-2

V60N-090RDUN-1-0-03/LSN-2-

V60N-090RDYN-1-0-03LSNS0

V60N-090RDYN-1-0-0LSNR

V60N-090RN-1-0-03/LSN-260

V60N-090RN-1-0-03/LSN–260

V60N-090-RSF-1-0-03-LSNR-200

V60N-090-RSFN-1-0-03

V60N-090RSFN-1-0-03/LSN-350-A00/64

V60N-090RSFN-1-0-03/LSNR-280

V60N-090RSFN-1-0-03LSNR-2

V60N-090RSFV-1-0-03/LSNR-200

V60N-090RSUN-1-0-01LSN-280

V60N-090RSUN-1-0-03/LLSN

V60N-090RSUN-1-0-03/LLSN-

V60N-090RSUN-1-0-03/LSN

V60N-090RSUN-1-0-03/LSN-

V60N-090RSUN-1-0-03/LSN-280

V60N-090RSUN-1-0-03/LSN-350-A00/64

V60N-110LDUN-2-0-03LSN

V60N-110LDYN-1-0-03/LSNR-2-300

V60N-110LSFN-1-0-03/LSN-280

V60N-110LSFN-1-0-03LSNR320bar

V60N-110-LSUN-2-0-03-LSNR

V60N-110RSFN-1-0-03/LSN

V60N-110RSFN-1-0-03/LSN-125-UNF

V60N-110RSFN-1-0-03/LSNR

V60N-110RSFN-1-0-03/LSNR/ZW

V60N-110RSFN-1-0-03/LSNR-2-300

V60N-110RSFN-1-0-03/LSNR-280

V60N-110RSFN-1-0-03/LSNR–280

V60N-110RSFN-2-0-03/LLSN-350-A00/76-C025

V60N110RSFN2-0-03/LLSN-C025

V60N-110RSFN-2-0-03/LLSN-C025

V60N-110RSFN-2-0-03/LSN-280-C027

V60N-110RSFN-2-0-03/LSN-350-A00/76-C024

V60N-110RSFN-2-0-03/LSN-350-C024

V60N-110RSFN-2-0-03/LSNR/ZW

V60N-110RSFN-2-0-03/LSNR/ZW-2

V60N-110RSFN-2-0-03/LSNR/ZW-280-C025

V60N-110RSFN-2-0-03/LSNR/ZW-280–C027

V60N-110RSFN-2-0-03/LSNR/ZW-350-C024

V60N-110RSFN-2-0-03/LSNR/ZW–C025

V60N-110RSFN-3-0-03/LSNR/ZW/350

V60N-110RSLIN-2-0-03LLSNS9021

V60N-110RSUN-01-0-02/LSN-2-124

V60N-110RSUN-1-0-03

V60N-110RSUN-1-0-03/LSN

V60N-110RSUN1003/LSN-160-UNF

V60N-110RSUN-1-0-03/LSN-200

V60N-110RSUN-1-0-03/LSN-280

V60N-110RSUN1003/N-120-UNF

V60N-110RSUN-1-0-03LSN

V60N-110-RSUN-1-0-03-LSN

V60N-110RSUN-2-0-03/LLSN

V60N-110RSUN-2-0-03/LLSN-157

V60N-110RSUN-2-0-03/LLSN-157N

V60N-110RSUN-2-0-03/LLSN-157Nm

V60N-110RSUN-2-0-03/LSN

V60N-110RSUN-2-0-03/LSN-

V60N-110RSUN-2-0-03/LSN-280-SAE-C2

V60N-110RSUN-2-0-03/LSN-350

V60N-110RSUN-2-0-03/LSNR/ZL/155-300

V60N-110RSUN-2-0-03/LSN–SAE-B4

V60N-110RSUN-2-0-03LLS

V60N-110RSUN-2-0-03LLSN

V60N-110-RSUN-2-0-03-LLSN-157

V60N-110RSUN-2-0-03LLSN3台

V60N-130LDYN-1-0-03/LSNR-2-300

V60N-130LDYN-1-0-03/LSNR-2-300/

V60N-90LDVN-1-0-02LS

V60N-90LDVN-1-0-02LSN

V60N-90LDVN-1-0-02LSN-250964

V60N-90LDVN-1-0-03

V60N-90RDN-1-0-02LSN-250946

V60N-90RDN-1-0-03/LSN-280

V60N-110RSUN-1-0-03

V60N-110RSUN-2-0-03LLSN

V60N-090RSFN-1-0-03/LSNR-280

V60N-110RSUN-2-0-03/LLSN-157N

V60N-110RSUN-1-0-03LSN

​​​